Welcome to our Blog page!

Our blogs are updated once a month, usually on the first day of the month. On this page, we offer advice, tips, and insights for becoming a safer driver and for better travels on Chico roads. Bookmark this page and remember to check back!

If you need auto repair service, don’t forget that you can schedule an appointment at this link for D&E Auto Repair in Chico. We look forward to seeing you! Remember that you are a part of the family at D&E Auto Repair in Chico. We’re located at 3328 Esplanade St., Chico, CA 95973.

Brake Rotor Problems

Disc brakes are called disc brakes because of the big metal disc – or rotor – that spins with the wheel.  The brake pads rub against the rotor to slow the vehicle.  In technical terms, the motion energy of the moving vehicle is transferred into heat energy by the brakes.  The job of the rotor is to absorb that heat and dissipate it into the atmosphere.  To do that effectively, the rotor needs a certain amount of mass (measured by the thickness of the rotor) and a good surface to mate with the brake pads.  Let’s talk about those two things.

First is the thickness.  A new rotor is nice and thick.  It can absorb a lot of heat and dissipate it effectively.  Over time, the rotor will wear away slightly.  If it wears away too much, there is not enough metal to take care of this heat transfer and the vehicle will not brake as well.  In fact, each rotor is stamped with the minimum thickness the rotor must have.  When the rotor reaches this “discard thickness”, it must be replaced.

Next in our consideration is the rotor surface.  Now this is not just about the quality of the rotor’s surface, but also about how evenly the brake pad sweeps the rotor.  Several things can affect the “swept area” of the rotor.  A common problem is a scored – or scratched – rotor.  When brake pads wear passed the point in which they should be replaced, metal parts of the brake can meet the rotors and grind grooves into the rotor.  Imagine putting new brake pads on a scored rotor. The pad would only contact the ridges.  This can significantly reduce the contact area and hurt braking performance.  When a rotor has been scored, it may be able to be resurfaced on a brake lathe which smooths the surface.  If the rotor is not thick enough to be resurfaced, it must be replaced.

Another common rotor problem is something called run out.  This is when the rotor is slightly off axis (crooked) so the brake pads do not contact the rotor fully and evenly.  Run out is measured in thousandths of an inch, so we are talking very small variations that can affect braking.  Run out can be caused by a bit of dirt or rust between the brake rotor and the wheel hub, or even by slight variations in the mating surfaces of the brake and hub.  Your technician can determine the cause and take the appropriate measures to restore proper brake pad contact.

When run out is not detected and corrected early, the rotor itself can wear unevenly leading to thickness variations.  This condition is called parallelism because the inboard and outboard surfaces of the rotor are no longer parallel.  The variations are small, measured in 10 thousandths of an inch, but they can significantly affect braking performance because of limited brake pad contact.  This condition used to be referred to as “warped” rotors, but that term is inaccurate.   If the rotor is still thick enough, the brake technician will correct the underlying run out problem and resurface the rotor to restore the contact surface. If the rotor is severely worn it must be replaced.

So, if you hear a grinding sound when you brake, get your brakes inspected as soon as you can to avoid possible rotor damage.  With run out and parallelism, you may feel a pulsation in the pedal as you brake.  If you feel a pulsation or if your pedal feels unusually soft or hard, bring your vehicle in for an inspection.  A qualified brake technician using quality brake parts can get you safely running – and stopping –as soon as possible.

Give us a call

CHICO, CA 95973
(530) 343-9703